-
-
-
Application
-
-
-
-
Service
Acceptance inspection and acceptance opinions of the working group for the completion environmental protection acceptance on-site inspection of the Nobot Intelligent Equipment (Shandong) Co., Ltd. intelligent equipment industrial robot construction project (Phase I)
Published Time:
May 10,2018
On May 5, 2018, Nobot Intelligent Equipment (Shandong) Co., Ltd. held a site inspection meeting for the acceptance of environmental protection facilities for the Phase I construction project of intelligent equipment industrial robots of Nobot Intelligent Equipment (Shandong) Co., Ltd.
2018 year 5 month 5 day, Nobot Intelligent Equipment （ Shandong ） Co., Ltd. held Nobot Intelligent Equipment （ Shandong ） Co., Ltd.'s intelligent equipment industrial robot construction project （ Phase one ） completion acceptance inspection meeting of environmental protection facilities. The acceptance working group was composed of the engineering construction unit （Nuo Boert Intelligent Equipment （ Shandong ） Co., Ltd. ） 、environmental assessment unit （ Liaocheng University ） 、monitoring unit （Liaocheng Environmental Science and Engineering Design Institute Environmental Testing Center ） and specially invited 2 technical experts （list attached）.
The acceptance team reviewed and verified the implementation of the project's environmental protection work on site, and based on the acceptance monitoring report and in accordance with the "Regulations on Environmental Protection Management of Construction Projects" 、"Interim Measures for Environmental Protection Acceptance of Completed Construction Projects" 、relevant laws and regulations, the environmental impact assessment report of this project and its approval requirements, etc., to accept this project. After careful study, the following acceptance opinions are formed:
1. Basic situation of project construction
（1）Construction location, scale, and main construction content
Nobot Intelligent Equipment （ Shandong ） Co., Ltd.'s intelligent equipment industrial robot construction project, located in Liaocheng High-tech Industrial Development Zone, south of Huanghe Road, east of Xiaomei River. The project in 2014 year 5 month started construction, with a designed production capacity of 3200 sets of intelligent equipment industrial
robots. As of 2017 year 12 month 31 day, the company has a production capacity of 2000 sets of intelligent equipment industrial robots. The project has built three production workshops. Part of workshop 1 includes a research and development center, forging workshop, assembly workshop, commissioning workshop, warehouse, office area, and living area, as well as other related auxiliary buildings. Workshop 2 is mainly a machining workshop, and workshop 3 is not yet
in use; the acceptance monitoring scope mainly covers production workshops 1 and 2, and the existing annual production capacity of 2,000 sets of intelligent equipment industrial robots.
（2）Construction process and environmental protection approval situation
2013 year 11 month, Nobot Intelligent Equipment （ Shandong ） Co., Ltd. commissioned Liaocheng University to prepare the "Environmental Impact Assessment Report for the Nobot Intelligent Equipment （ Shandong ） Co., Ltd. Intelligent Equipment Industrial Robot Construction Project." On 2014 year 1 month 10 day, the Liaocheng Environmental Protection Bureau High-tech Industrial Development Zone Branch conducted the Nobot Intelligent Equipment （ Shandong ） Co., Ltd. "Approval of the Environmental Impact Report for the Intelligent Equipment Industrial Robot Construction Project" Liaokaihuan Report [2014]2
[2014]2 No.; the project was completed on 2014 year 5 month started construction, with a designed production capacity of 3200
sets of intelligent equipment industrial robots. As of 2017 year 12 month 31 day, the company has a production capacity of
2000 sets of intelligent equipment industrial robots. Nobot Intelligent Equipment (Shandong) Co., Ltd.
in 2018 year 1 month commissioned the Liaocheng Environmental Science and Engineering Design Institute Environmental Testing Center to conduct completion environmental protection acceptance monitoring and prepared the "Nobot Intelligent Equipment （ Shandong ） Co., Ltd. Intelligent Equipment Industrial Robot Construction Project （ Phase 1 ） Completion Environmental Protection Acceptance Monitoring Report ."
（3）Investment situation
The total investment of Phase 1 of this project is 23459 ten thousand yuan, of which environmental protection investment is 120 ten thousand yuan, accounting for 0.51% of the total investment.
（4）Acceptance scope
Nobot Intelligent Equipment (Shandong) Co., Ltd.'s intelligent equipment industrial robot construction project
（ Phase 1 ） , with an annual production capacity of 2000 sets of intelligent equipment industrial robots and their environmental protection facilities. 2. Changes in the project
The project was completed on 2014 year 5 month started construction, with a designed production capacity of 3200 sets of intelligent
equipment industrial robots. As of 2017 year 12 month 31 day, the company has a production capacity of 2000 sets of intelligent equipment industrial robots. The construction unit will conduct phased acceptance.
3. Construction of environmental protection facilities
（1）Wastewater
The project's water use mainly consists of production process recycled water and domestic water. Production recycled water is regularly replenished and not discharged; domestic water is pretreated by a septic tank and then discharged into the municipal sewage pipe network and into the Liaocheng Economic Development Zone wastewater treatment plant.
(II) Exhaust Gas
The exhaust gas generated by this project mainly includes a small amount of particulate matter and welding fumes generated during the machining process of robot parts. Welding fumes are purified by a welding fume purifier and then discharged into the workshop in an unorganized manner; a temporary canteen is set up in the factory area, and the canteen oil fume exhaust gas is purified by an oil fume purifier before discharge.
(III) Noise
The main noise sources of this project include the noise generated by the operation of various machine tools, punching machines, etc., and the noise of air compressors during the robot assembly process. The main equipment is evenly distributed in the factory building, and noise reduction measures such as sound insulation, vibration damping, and distance attenuation are adopted.
(IV) Solid Waste
The solid waste of this project mainly includes waste grinding fluid, waste engine oil, machining burrs and scraps, waste packaging materials, and office and domestic garbage. According to the information provided by the enterprise, waste cutting fluid generation 0.8t/a ，Hazardous waste code HW 09 900-006-09 ，waste hydraulic oil generation is
1.0 t/a ，Hazardous waste code HW08 900-218-08 ，both of which belong to hazardous waste, the enterprise entrusts Shanxi Huifeng Yili Environmental Protection Technology Co., Ltd. for disposal, currently temporarily stored in the hazardous waste room; The solid waste generated by the machining process of robot parts mainly includes aluminum alloy and stainless steel edges
and scraps and iron filings, with a generation of 120t/a, all of which are sold for comprehensive utilization; domestic garbage is collected and processed by the sanitation department.
(V) Other Environmental Protection Facilities
1. Online monitoring device
According to current requirements, the enterprise does not need to set up an online monitoring device.
2. Others
The distribution of environmentally sensitive points around the factory area has not changed since the environmental impact assessment approval.
(VI) Environmental Protection Facility Debugging Effect
Liaocheng Environmental Science and Engineering Design Institute Environmental Monitoring Center issued the "Nobot Intelligent Equipment （ Shandong ） Co., Ltd.'s intelligent equipment industrial robot construction project （ Phase 1 ） Completion Environmental Protection Acceptance Monitoring Report", during the acceptance monitoring period, the project production conditions were stable, and the production load was 90%, which meets the requirements that the acceptance monitoring should be carried out under stable operating conditions and production load reaching the design production capacity load of 75% above. The monitoring results show:
1. Exhaust gas
In the two-day monitoring of unorganized exhaust gas, the maximum monitoring concentrations of non-methane total hydrocarbons and particulate matter were respectively 1.06mg/m3、0.318mg/m3 meet the "Comprehensive Emission Standard for Air Pollutants " (GB/T 16297-1996) in the table 2 The limit value for unorganized emission monitoring.
2. Wastewater
During the acceptance monitoring period, the total outlet of the factory area pH The measured range is 7.11~7.46 ，Ammonia nitrogen, COD Cr 、 SS The daily maximum values were respectively 17.1mg/L、188mg/L、98mg/L ，all meet the "Water Quality Standard for Wastewater Discharge into Urban Sewers" （ GB T 31962-2015 )B grade standard.
3. Noise
The noise acceptance monitoring results show that the daytime noise values at the east, south, west, and north boundaries of the factory are in the range of
53.3~60.3 dB(A), which meets the Class 3 standard requirements of the "Emission Standard for Environmental Noise at the Boundaries of Industrial Enterprises"
(GB12348-2008).
4. Solid waste
The solid waste of this project mainly includes waste grinding fluid, waste engine oil, machining burrs and scraps, waste packaging materials, and office and domestic garbage. According to the information provided by the enterprise, waste cutting fluid generation 0.8t/a ，Hazardous waste code HW 09 900-006-09 ，waste hydraulic oil generation is
1.0t/a ，Hazardous waste code HW08 900-218-08 ，both of which belong to hazardous waste, the enterprise entrusts Shanxi Huifeng Yili Environmental Protection Technology Co., Ltd. for disposal, currently temporarily stored in the hazardous waste room; The solid waste generated by the machining process of robot parts mainly includes aluminum alloy and stainless steel edges burrs and scraps and iron filings, with a generation of 120t/a, all of which are sold for comprehensive utilization; domestic garbage is collected and processed by the sanitation department.
4 .Total amount of pollutant discharge
According to current regulations, the enterprise does not need to apply for the total amount of pollutant discharge. V. Environmental Impact of Project Construction
The project construction has carried out an environmental impact assessment and basically implemented the environmental impact assessment document and its approval requirements. During the acceptance monitoring period, the exhaust gas, wastewater, and noise generated by the project can meet the standards discharge, and solid waste can be properly handled.
VI. Acceptance Conclusion
Nobot Intelligent Equipment (Shandong) Co., Ltd.'s intelligent equipment industrial robot construction project
（ Phase 1 ） In the implementation process, relevant environmental protection measures have been implemented in accordance with the environmental impact assessment and its approval requirements, no major changes have occurred during the project construction process; the pollutant emissions monitored during the acceptance meet the relevant national emission standards, and the acceptance report does not have any major quality defects.
Given that the project basically meets the acceptance criteria and does not involve any unqualified acceptance situations as stipulated in the "Provisional Measures for the Acceptance of Construction Project Completion Environmental Protection", the acceptance working group agrees in principle that the environmental protection facilities of this project pass the environmental protection acceptance.
Given that the project basically meets the acceptance criteria and does not involve any unqualified acceptance situations as stipulated in the "Provisional Measures for the Acceptance of Construction Project Completion Environmental Protection", the acceptance working group agrees in principle that the environmental protection facilities of this project pass the environmental protection acceptance. The environmental protection facilities of this project have passed the environmental protection acceptance.
VII. Subsequent Requirements
1 Strictly follow the "Standard for Pollution Control in Hazardous Waste Storage " (GB18597-2001) and the requirements of the amendment to store and manage the generated hazardous waste, and entrust a qualified unit for timely disposal. Dispose of the generated hazardous waste in a timely manner by entrusting a qualified unit.
VIII. Acceptance personnel information is shown in the attachment.
Nobot Intelligent Equipment (Shandong) Co., Ltd.
April 15, 2018 View Source File
BLOGS
Nobot Group's 2025 Kick-off Event: A Team Building Activity Focused on Unity and Power
This opening ceremony was both a knowledge-boosting session, allowing employees to continuously grow through learning, and a team-building event, bringing everyone closer together. It impressed upon each employee that in today's increasingly competitive market, only by continuously learning new knowledge, daring to innovate, and maintaining teamwork can we remain undefeated. With the collective efforts of all employees, Nobot will surely ride the waves and achieve even greater success on this new journey, steadily advancing towards higher goals!
Nobot was invited to attend the Belt and Road International Exchange Conference
On July 28, 2024, the 2024 Liaocheng "Belt and Road" International Exchange Conference and the Unveiling Ceremony of the Central Asia International High-end Talent Joint Training Base were held in the Liaocheng High-tech Zone University Science and Technology Park. Professor Tursunbayev Zaporotot, President of Osh Technological University of the Kyrgyz Republic and corresponding academician of the Kyrgyz Academy of Engineering, and Academician Smaylor Erta of the Kyrgyz Academy of Engineering and the Russian Academy of Natural Sciences, among other experts and scholars from "Belt and Road" countries, participated in the event. Liaocheng Deputy Mayor Wang Gang and Zhang Ya, Party Secretary and Director of the Management Committee of the High-tech Zone, attended the event and delivered speeches.
This training event not only provided a valuable learning opportunity for company managers and key personnel, but also built a platform for communication and sharing. During the training, everyone actively interacted and discussed enthusiastically, exploring effective ways to improve management capabilities together. Through this training, everyone has gained rich knowledge and skills, but more importantly, it has inspired confidence and motivation for the future.
How to use a five-axis machining center efficiently? Today, let's learn a few practical steps!
When using a five-axis machining center, the equipment must first be adjusted to ensure that the workpiece and fixture dimensions precisely match, and that the zero points of each axis are accurately adjusted.
Why do composite materials require 5-axis CNC machining?
Composite materials are widely used in various fields such as aerospace, automotive, construction, energy, energy storage, infrastructure, marine, pipelines and tanks, sports and entertainment, and transportation due to their light weight, high fatigue resistance, and strong fracture resistance. Among them, aerospace and automotive industries are the largest application markets for composite materials. Five-axis CNC plays an important role in the processing of composite materials. Why do composite materials need to be processed using five-axis CNC?
Dual-station five-axis machines offer several significant advantages. First, while one station is being machined, the other can be used for material loading and unloading, ensuring continuous, non-stop machining and significantly improving production efficiency. Second, the dual-station design makes operation more convenient and reduces waiting time. However, dual-station five-axis machines typically cost more than single-station machines and may require more operating and maintenance space.
Nobot Intelligent Equipment Group Co., Ltd.
Pre-sales consultation:86-635-2932233
Fax:86-635-2945333
After-sales consultation:86-635-5086881 / 86-635-2936881
National unified service hotline:86-400-823-3356
Email:nuobote@nobot.cc
Address: No. 1 Plant, No. 88 Huanghe Road, Gaoxin District, Liaocheng City, Shandong Province
copyright © 2025 Nobot Intelligent Equipment Group Co., Ltd.